Employers should "provide protection from falling objects" - for example, a heavy chain.Yes but you are stood on the ground so surely you are not working at height because you are not at height.
Employers should "provide protection from falling objects" - for example, a heavy chain.Yes but you are stood on the ground so surely you are not working at height because you are not at height.
Employers should "provide protection from falling objects" - for example, a heavy chain.
I should probably leave this, but I've done enough work for Health and Safety organisations to know: a) People get horribly injured at work so often it's not funny and b) The reasons are often completely banal and avoidable. Sorry, I'll get off my hobby horse.Well that is mental. Just wear a hard hat or something and be careful.
I should point out that it is good practice to try and avoid sending fitters down below the coaches with hi-vis and helmets at the design stage; CAF have essentially designed the risk of injury out of the coupling with the use of Dellners (which also conveniently transfer the required ETS through the train without the need for connecting nearly as many jumper cables).Well that is mental. Just wear a hard hat or something and be careful.
The Dellners do not transfer the train supply on the sleepers. If they did, they wouldn't need ETH jumpers.I should point out that it is good practice to try and avoid sending fitters down below the coaches with hi-vis and helmets at the design stage; CAF have essentially designed the risk of injury out of the coupling with the use of Dellners (which also conveniently transfer the required ETS through the train without the need for connecting nearly as many jumper cables).
Besides, a hard hat is next to useless against a pair of buffers crushing an engineers' skull laterally.
Both 020 and 032 had pans up coming out of the ETD into the station.92020 was out today with its Pantogtraph up paired with 92032 at Crewe, 032 had it's pan down
Ah ok, sorry, I only saw it for a few seconds, must have been the small amount of time it was down.Both 020 and 032 had pans up coming out of the ETD into the station.
View attachment 58305
032’s was just down momentarily as the driver swapped pans on 032 to run the locos back to the ETD.
020’s first run on the mainline under her own power since April 2001!!
Or even Midnight Teal.........Will all the 92s in the CS pool receive the Midnight Deal livery?
Ran off on Saturday to Crewe... https://flic.kr/p/QxmsZt92014 off the garston car job 66787 now taken over.
92010 on 1M16 was in bother overnight with loss of air at Beattock Summit; 90048 was made ready to assist but in the end wasn’t needed and the train is currently running about half an hour late around Shap.
Was failed at Waverley last Wed night and Mon night and replaced by the Carstairs engine both times. Worked OK Thu and Sun night.That loco has failed twice in the past few weeks or so, something not right with it.
Other than 92006 at Brush only those locos that have received CS livery so far will be receiving it.
And here she is... and yes, that is 92006 moving under her own power on the mainline for the first time in 13 years after panning up first time and booting up without so much as a grumble.The aforementioned 92006 has today been released from Brush and was hauled to Crewe H.S. from where it should undergo some test runs over the next few days.
Great video tim whats the next plans for it a run out on the cars soon?And here she is... and yes, that is 92006 moving under her own power on the mainline for the first time in 13 years after panning up first time and booting up without so much as a grumble.
Test runs to start with - all being well will be out on the WCML over the coming days. Stafford and/or Preston are possibitlies for tomorrow.Great video tim whats the next plans for it a run out on the cars soon?
Awaiting collection by 006 very shortly...92033 in teal livery was stabled at Preston in the RES sidings yesterday morning. Any ideas why?
92s can do this, but (if at all) only when working HS1/Tunnel.Why is re-gen not used?